Show edge edge-3 service highavailability (Shows edge-ID edge-3 high availability status) Show edge edge-3 ip route (Shows edge-ID edge-3 routing table) Show edge edge-3 ip bgp (Shows edge-ID edge-3 bgp status) Show edge edge-3 ip ospf (Shows edge-ID edge-3 ospf status) Show edge edge-3 system network-stats (Shows edge-ID edge-3 network stats including errors) Show edge edge-3 firewall (Shows edge-ID edge-3 firewall rules as well as number of packet matches) Which packets are currently flowing through the edge device) Show edge edge-3 flowtable (Shows edge-ID edge-3 current flow table. Show edge edge-3 arp (Shows edge-ID edge-3 arp cache) Show edge edge-3 nat (Shows edge-ID edge-3 NAT rules as well as number of packet matches) Show edge edge-3 eventmgr (Show edge-ID edge-3 event manager, displays errors, health status and system events) Show edge edge-3 version (Show edge-ID edge-3 version, build number and kernel) Show edge all (Show edge-ID, name, version, size and status of each edge device) Displays Host-ID, Host-Name and VDS Name) Show logical-switch list vni 5002 host (Show hosts on logical switch 5002. Show logical-switch list all (Show each logical switch, UUID, VNI and transport zone) Show controller list all (Lists all controllers connected to this NSX Manager. Show host host-247 (Show VMware ESXi Host Id 247 containing VM’s, VM Id and Power Status) Show cluster domain-c21 (Show cluster-id domain-c21 VMware cluster, contains hostname, host ID and Install Status) Show cluster all (Show VMware cluster, datacenter name and firewall status) Replace follow with last 10 to show the last 10 logs) Replace follow with reverse to show the logs in reverse time order. Show log appmgmt follow (Tails the appmgmt log live. Show log system follow (Tails the system log live. Show log manager follow (Tails the manager log live. Show ethernet (Shows ethernet port settings and statistics) This command is located within enable mode) Show filesystems (Shows filesystem, size, used, available and mounts. Show clock (This command displays the system time and date. Show tech-support (Show Cisco tech-support info. Show system uptime (Shows uptime in days, hours, minutes, seconds) Remove | grep vxlan to view the entire log)Ĭat /var/log/vmksummary.log (View the ESXi vmksummary log)Ĭat /var/log/vmkwarning.log (View ESXi vmkwarning.log) Ping -S vxlan -I vmkx (Ping the destination IP using the vxlan stack and Interface vmkx, replace x with your vxlan vmk number)Ĭat /var/log/vmkernel.log | grep vxlan (Look for keyword vxlan within the ESXi vmkernel.log. Displays vmknic name, switch port ID, VDS Port ID, Endpoint ID, VLAN ID, IP address, Netmask, IP Acquire Timeout, Multicast Group Count, Segment ID) Displays Inner MAC, Outer MAC, Outer IP and Flags)Įsxcli network vswitch dvs vmware vxlan vmknic list –vds-name=VDS1 (Shows VXLAN vmk’s. Shows VXLAN ID, Multicast IP, Control Plane, Controller Connection, Port Count, MAC Entry Count, Arp Entry Count, Control Plan Out-Of-Sync status)Įsxcli network vswitch dvs vmware vxlan network mac list –vds-name VDS1 –vxlan-id=5002 (Shows MAC address list associated with VDS and VXLAN ID. Displays VDS name, MTU, segment ID, gateway ID)Įsxcli network vswitch dvs vmware vxlan network list –vds-name VDS1 (Displays VXLAN network info with specified VDS. etc/init.d/netcpad status (Checks that the netcpad User World Agent (UWA) is running)Įsxcli network ip interface ipv4 get (Displays a list of vmkernel nics, ip address, subnet, broadcast)Įsxcli network ip interface list –netstack=vxlan (Displays information on the vmkernel nics that are configured for VXLAN such as MAC Address, Portset, Netstack, VDS Name, MTU)Įsxcli network vswitch dvs vmware vxlan list (Displays the VDS that is associated with the ESXi hosts VTEP. etc/init.d/vShield-Stateful-Firewall status (Checks that the vShield-Stateful-Firewall User World Agent (UWA) is running) Displays if the module is Loaded and Enabled) Version and Dependencies)Įsxcli system module list | grep nsx (List of NSX modules loaded in the host. (Updated 9th-October-2020) VMware ESXi HostsĮsxcli software vib get –vibname esx-nsxv (Displays information relating to NSX datapath and host tools. If you come across some NSX-V CLI commands that you would like to share with everyone, use the contact us page or leave the commands in the comments below and i’ll be sure to add them to this NSX cheat sheet. On this page I will be constantly adding VMware NSX-V CLI commands as an easy reference NSX Cheat Sheet
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |